J301P1 General Electric Range - Instructions

The bake element was completely missing from the stove. There were two wires sticking out of the back of the oven, one with a terminal on the end and the other with the insulation still on and no bare wire showing/ The right side mounting screw was there..

The left mounting screw hole on the oven had been drilled out oversized, so I drilled another hole in the mounting plate above the original., after attaching the element with a single screw.

I removed the one screw, removed the bake element and pulled the electrical wire without the terminal end. Next, I put a terminal on the wire and attached the wires to the element. Finally I installed the element with the two screw into the rear of the oven.

Unfortunately the element didn't work, so my next step is to trace the wiring and determine if a switch or thermostat might be faulty. I have checked the continuity of the wires from the bake element to the thermostat.

More in chaper two..

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you

Removed screws that hold element in place. Disconnected the two electrical leads. Put the new element in place, hooked up the two leads and installed the the screws that hold the element in place.

Before ordering the new part, made sure the problem was the burner and not the wiring in this very old stove by putting an ohmmeter on the terminals of the burner after removing it. Since it showed no conductivity, the burner was bad (could have put the voltmeter on the wires and turned on the power to ensure power was coming in......but did not want to mess with 240 volt/high amperage. With power off at the breaker, installed new burner. One caution... since the wire on the burner terminals is pretty soft, don't bend them by putting too much torque on the screws. This turned out to be my only problem.....I had to clean up the screws and work them through the copper terminals with the burner outside the oven before attempting to screw them on the wire connectors in the oven. Not a big problem, but if you bend the terminals too much when you install the burner in the oven, you run the risk of shorting them together, or breaking one. And that would be a big problem.

First I removed the two screws that hold the element in place. I pulled the element out and disconnected the two wires that hold it in place. I reversed the process for the new element and viola! The oven works just great. The element actually arrived a day earlier than expected. Thanks Parts Select!

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.

Turned off breaker,first . Then removed 2 nutscrews and pulled unit out , 4 inches ,removed 2 nutscrews joining the 2 wires and the 2 terminals of the bottom element. Removed bottom unit and replaced with new unit . reversing the process. Turned breaker on and tested the oven. Works fine. Took less than 15 minutes.

turn power off at circuit breaker box, remove old coil from oven, attach the new coil and attach to wall of the oven. Very easy to repair.

First turned off the circuit that controlled the power to the Stove/Oven.
Then I removed the screws that hold the element in place.
I pulled the element out a few inches and disconnected the wires.
I attached the wires for the new element.
I replaced the screws.
I turned on the circuit.

And to reward myself baked a Coffee Cake. Yum!

Removed 2 screws with nutdriver.Pulled element out to expose wiring and disconnect 2 wires also with nutdriver. Reverse process. Unit reaired.

removed the old heating element which had about two screws and two connecting wires and replaced it with the new one. I twas so fast and easy. I thought I was going to need a new Oven!!!!!Thank goodness for your website!!!!!

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.