JD900BK1BB General Electric Range - Instructions

Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Good Luck, PartSelect has all the parts you need, this my second getting a part from them.

The burner would work but you could not regulate the heat. I ordered and replaced the control switch for that burner. The part was like for like and reasonably priced compared to other websites and dealer. The picture showed that it was identical. I ordered one day and it was here the next. I had drawn a diagram of where the wires went on the old switch so it was very easy to replace. Probably took me 15 minutes or so. Works perfectly and by buying from this website it saved me a few bucks.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, removing the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.

The hardest part was getting the correct part. I trusted the on line number and the first part I received was incorrect. I should have taken the part number off the old switch. When I did, I found out that the part number changed when I tried to order it. When the part came, the wiring instructions were not even close. I just took one wire at a time off the old switch and put it on the same terminal of the new switch. The repair was/is very simple made complex and too much time because of a wrong part and incorrect wiring instructions. As far as getting the incorrect and correct parts through the mail it was very fast. Received both parts in less than 3 days. A bonus is that I sent the old switch back for a rebate. Thanks for that.

The repair was quite simple. Just removed a few screws and had to insert the panel band. The problem we had was that the F7 code didn't advise which part was needed. There were two possibilities when we searched online, the electronic range control or the control board overlay. So we guessed and ordered the electronic range control first. It was not that, so we had to reorder and purchased the control board overlay. That was it!! So the code should state which part is needed. What should have been a very simple process was made difficult because GE didn't specify which part was needed.

Took off the knobs and retainer nuts. Carefully setting them on top in the same order as they came off. Unscrewed the bottom retainer screws. Removed the main control trim. Unscrewed the top retainer screws. Carefully pulled the broken control assembly panel out of the wire harness. Reversed the procedure to install the new Panel.
Found the part quick and easily on your site and had it shipped next day. Wonderful Experience!

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

Basically removed the screws holding the op on and removed the vent from back. Just "figured it out" and now it works. Wish I could be more helpful. Recommend moderate experience and confidence.

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

Disconnected breaker. Removed knobs, plastic retaining nuts mounted to each switch shaft. Removed four 1/4 inch hex head screws on front panel and two screws securing defective switch. Removed bad switch, and replaced with new part. Took photo of wiring before removing old part. Referred to photo to ensure correct wiring of new part. Reassembled front panel in reverse order of disassembly. Turned breaker to on, and tested new switch. All worked well.

Looked up the part, ordered it, and it was there in 3 days. It was slightly different than the old control, but a very well-written set of instuctions detailed which wires to move to which terminal. The entire repair took about 30 minutes, including moving the range out, replacing the control, and push the range back in place. Works perfectly.

Removed panel to gain access, removed wires from switch from burner that was not operating and attached them to switch for burner that was working. Burner worked, problem identified. Replaced bad switch with new switch. Problem solved.