JK1902 General Electric Range - Instructions

extremelyquick delivery on standard mail and so easy to install and really the lowest price. so happywith this company

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.

removed old element rewired new element,turned back on power

The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!

First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.

Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.

First I turned the power to the stove off at the breaker box. Next I removed the two screws holding the old element in place against the back wall of the oven. I gently pulled the element forward. I wound a couple lengths of spare colored wire around the two electrical wires before disconnecting the retainer screws at their connection points. This insured that the electric wires would not fall back inside and behind the firewall. I then disconnected the screws holding the electrical wires to the broiler element. I removed the element from the oven and discarded it. I then connected the screws through wires and the connecting points of the new element. I removed the spare wires hold the electrical wires. I positioned the broiler element in place and screwed in the retainer screws securing it in place. I turned the breaker switch to the "on" position and tested the new broiler element. It tested fine. Job done in 15 to 20 minutes. An able bodied person could do it in less than 10 I'm sure.

I diagnosed the problem as a burned out element. Received the part the next day (very quick service) My husband replaced the old element with the new. My broiler still doesn't work. I don't blame the company, my diagnoses was wrong. I have called the appliance repairman and it will probably be an expensive fix.

Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!

Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussing. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.

Broiler element failed catastrophically (with light flashes) while in use (1986 GE self-clean oven/four burner stovetop). Part number embossed on element plate - very difficult to see - took digital photo while still in oven and magnified. Easy to search for part. Good price, prompt delivery. Removal of old and install new awkward because of access angle and my decreasing nimbleness, as well as oven control thermocouple and support bracket in way. But no technical difficulties. Hex head metal screws holding in element; Notched phillips metal screws holding bracing bracket (easier to put element in by removing one side of bracket). Screws difficult to remove as in much used oven 26 years, and thermocouple partially blocking socket ratchet wrench. Would have been easier with 1/4" short extension. Before detaching element, I used twist ties around the leads tied to a large plastic clip so as not to lose them into oven back. PartSelect part was made by GE, not secondary source. Perfect replacement for this old part - still available.

Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.

Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.

Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.