JDS26BW2WH General Electric Range - Instructions

I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.

Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.

THANKS SO MUCH!!!

Removed the two screws, pulled out old element, installed new element, and reinstalled screws.

Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!

Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes.
Reading previous reviews was quite helpful

first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

Cut Wires to old terminal block and wired in new Terminal Block

It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!

took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!