J466*03 General Electric Range - Instructions

got new part delivered two days after ordering. I turned off breaker, used a 1/4" wrench to remove the fasteners holding the heating element to the back inside wall of the oven. used screw drivers (one Phillips and one flathead) to remove the screws holding the heating element to the wires. ensure you pull the wires slight out (easily) to ensure they don't pull back into the oven wall. unplug the element from the wires, install new element in reverse fashion and voila, done.

Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!

Replaced old bake element by removing two screws holding it to back of oven. Disconnected old bake element from lead wires by removing two other screws. Installed new bake element by reversing the process. Only issue is that the tabs on the element that connect to the leads are easily bent and you need to use vise-grips to keep from bending them. Otherwise, very easy. Thank you PartSelect.com for stocking this item that I used to repair my 45-year old GE range!

pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.

Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!

I replaced the element. The new part arrived within 48 hours of being ordered. It worked. The part that sticks out the back of the oven with the connections was a little shorter on the new element which made it more difficult to put the wires on but it was not too difficult.

Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!

Simply removed two screws to detach element from oven wall, removed two terminal wires then reversed the procedure to install the new element.

The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.

removed the old element, inserted the new one.

My oven is so old that the model # tag has been scrubbed blank. I search your site by Brand name and oven description. I found the pictured element in your listing and sized it up. Part arrived as promised. It was simple to install - power down oven via circuit breaker and remove 4 ea screws and removed defective element. Install new element and reattach via screws. Turn on circuit breaker and power up oven to test - all working fine.

First, I turned off the power at the breaker box. Then, I removed the 2 screws attaching the bake element to the back wall of the oven. Next, I pulled the element out a few inches and removed the screws holding the element to the wires at the rear of the oven. Finally, I reattached the new element to the wires with the screws and then reattached the element plate to the rear wall of the oven. I turned the power back on at the breaker box, and tried the new element. It worked! Also, shipping was real fast, like 2 days from the time I placed the order to receiving the element.

It was easy and worth doing myself because a repairman said, he could do it for $50.00 dollars. I spent $28.00 which includes the shipping cost.

1.Shut off power to stove. 2. Lift up non-working burner. 3. Unscrew retaining screw that allows burner to tilt. 4. Lift burner out. 5. remove clips from ceramic holder. 6. Unscrew 3 screws holding element, write down which color is attached to which element, or label wires. 7. unpack new element, directions say to cut off and tip the leads with solder, but I re-used the old circle connectors. 8. Screw the wires back on the new element (using nutdriver) 9. place element in new ceramic holder provided, and clamp shut. 10. place element in stove top opening and screw in retaining screw (honestly I could not get this to work correctly, so I just left the element sitting in the hole). 11. Turn power back on. This could take as few as 5-10 minutes, but I allowed 1/2 hour for turning power on and off or moving the stove to unplug it.

Delivery of the replacement element was quick.Two days after I ordered. My husband replaced it and said it was easy. He just had to unscrew the old element and disconnect the terminals on the back.I thought I was going to have to buy a new stove,just because my oven element wasn't working. Many thanks!