J416V2 General Electric Range - Instructions

I just replaced them.

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

the replacement items fit really good. It was a matter of remove and replace,

Disconnected range from power. Removed small / lower shield that protects element connectors from rear of range. Disconnected the power lines from the element using screwdriver. Removed racks and liner from oven. Removed screws at rear of oven box that hold old element. Removed the old element. Reversed steps to install replacement heating element. Tested oven heating using oven thermometer.

replace with new one

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

Turn off electricity to the oven. A socket set was needed for the small screws in my old oven. Once the screws were removed the element came off easily from two wires in the oven. You have to be careful when handling the wires that they don’t fall back into the oven. The new part was attached to the two wires, screws were tightened on the new element and that was it. When the oven was turned on the new element smoked a little but I saw on the video that is normal.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

I first unplugged the stove as that was easier than going to turn off the breaker. I removed both oven racks for more room to work. There were two screws to removed inside the back of the oven. After pulling the element out a few inches I was able to unscrew the two screws that held the wires onto the element. I made sure to note which wire went on which side. Then did everything backwards with the replacement element.Plug the oven back in and make sure it works. This was the easiest repair I have ever had to make on any appliance! It's good to note the new element could heat much faster and hotter than the old one. I plan to check the temp when baking. The replacement one also hinged so cleaning in the future will be much easier as well.

Because of the age of the oven it took a little time to loosen the screws that held the element in. Once the screws were removed it was a matter of pulling the element out about 3 inches and disconnected the two wires, then it was a matter of repeating the steps in reverse. Very quick and easy