RS743G402 General Electric Range - Instructions

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

Followed instruction that came in the new parts. Each element took about 10 minutes to remove, inspect the wires, clean the connections and reconnect the new elements. The element covers that came with the kit were easy to install, and everything fit just fine. Most important thing is to turn of the electrical power to the unit BEFORE you start.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Unplug range from its 220V source. Make sure range is not hot from recent usage. You’ll need a #2 Philips driver, preferably one with 14-18 inch length. The old screws will likely be very stubborn about coming loose. Two of them hold bottom element in. Remove the back panel so access to the two connectors on the bottom element are easily removable. Be very careful not to the let the wire connectors from the heating element drop down into the insulation. For the top element, there are four screws holding it in place, I found it was easier to access these two screws leaning the range backward at a slight angle. Take special care again not to let the wires drop down into the insulation. The connectors to the old element will likely need some extra effort to remove. The reconnection to the new elements should be ok. Make sure all screws go back in that were removed. The new elements will be amazing, and baking and broiling will be like new again.

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

Ordered part, took old bake element out, installed new bake element. It was real easy.

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

lift eye slide in bowl and trim ring, put the eye back down,

Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.

Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.

Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating element. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

Followed the enclosed instructions