JBP36G4W5 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from TRAVERSE CITY, MI
- Parts Used:
- WB2X831D
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
bottom drawer guides
Snapped in place (4)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barnaby from Alameda, CA
- Parts Used:
- WB17X5051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Corrosion of terminal block led to poor performance of elements.
Unplugged oven from mains.
Removed screw holding terminal block to oven top. Used screwdriver to remove clip holding protective card to terminal block. Removed Philips screws holding wires onto terminal block.
Replacing the terminal block was just doing the above instructions in reverse. The only thing different was to put the speed clip on the range top before attaching the block to the range top.
Removed screw holding terminal block to oven top. Used screwdriver to remove clip holding protective card to terminal block. Removed Philips screws holding wires onto terminal block.
Replacing the terminal block was just doing the above instructions in reverse. The only thing different was to put the speed clip on the range top before attaching the block to the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
Esisting trim ring and drip pan severly corroded and stained.
Order special parts from PartSelect. Electric Burner was rare 3 level 4,6 8 inch selectable. Raise burner unit on hinge. Place drip pan, then trim ring under burner. Lower burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L. from Houma, LA
- Parts Used:
- WB17X5051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part worn out
Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from monroe, WI
- Parts Used:
- WB17X5051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
burner wouldn't heat
I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Martins Creek, PA
- Parts Used:
- WB24X5097
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Solenoid failed due to excessive heat.
Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from redding, CT
- Parts Used:
- WB17X5051
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Stove element not working
The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. from Durham, NC
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Element burned out
Partselect had the right part, clearly indicated in the diagrams and menus. Shipped quickly. Easy to use web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles G from Columbia, MD
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Range element failed to heat
Replacement element also failed to heat.
Possible that the problem is with the stove itself, not with the surface element.
Possible that the problem is with the stove itself, not with the surface element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Canyon Country, CA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Element wouldn't heat
Just pull out the current element and plug-in the new one. Part was received in 24 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Jefferson, OH
- Parts Used:
- WB32X5036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace drip pan
Could not find the right pan locally. This was the right one! Fast shipping also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Madison, WI
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Burner was crappin' out after 20 years of service
Pulled out the old burner that was held in by a metal spring clamp. Pushed the new one in.
Good as new.
Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yi from Miami, FL
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old surface unit was not generating heat
We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!
Was this instruction helpful to you?
Thank you for voting!