JGP330BEKB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry L from Puyallup, WA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from las vegas, NV
- Parts Used:
- WB13X46909
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HENDERSONVLLE, NC
- Parts Used:
- WB02T10461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from UPLAND, CA
- Parts Used:
- WB18T10339, WB13X46909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Igniters would not turn off
Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Broadalbin, NY
- Parts Used:
- WB02T10461
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CYPRESS, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very easy
there were no grate pads so it was easy to add them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Ashland, MA
- Parts Used:
- WB29K10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn and pitted burner caps
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chelagh from Fredericksburg, VA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
Nothing technical.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tijeras, NM
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate foot bdroke off allowing grate to scratch cooktop
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Simi Valley, CA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Kenner, LA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Ogdensburg, NY
- Parts Used:
- WB16K10055, WB29K10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this instruction helpful to you?
Thank you for voting!