JK25202 General Electric Range - Instructions

The complete repair was quick, easy, and painless. Not only did my item show up sooner than I thought the whole replacement took only 15 minutes, tops, to complete. I even had my 18 months old daughter helping too.

First and foremost I turned off the power to the oven by tripping the circuit breaker in the basement. Then verifying that the oven or stove top did not work to insure that the correct circuit breaker was tripped.

Then I removed the two mounting bolts on the support plate, that holds the element in place, from the rear wall of the oven. Then slide out the element just far enough to gain access to the wires that are attached to the element, about 3-6 inches. Carefully removed the two wires from the element with a screwdriver, noticing how flexible the ends of the element were. Removed the old element out of the oven. Placed the new element into the oven and then reattached the two wires to the new element terminals, being careful not to bend the ends of the element too much, very flexible!! Slide the element back into place and then reattached the mounting bolts. Turned all power back on to the stove and then turned the oven on and presto!, my oven is fully functional again.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.

First I removed the two screws that hold the element in place. I pulled the element out and disconnected the two wires that hold it in place. I reversed the process for the new element and viola! The oven works just great. The element actually arrived a day earlier than expected. Thanks Parts Select!

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

I simply removed the 2 mounting screws, pulled the element out a few inches, disconnected the 2 screws holding the wires to the terminals and reversed the order for assembly.

REMEMBER to turn off the breaker at the panel because the wires are still hot even though the oven control itself is off (trust me!!!).

Excellent service and fast delivery from partselect.com........ I'd gladly deal with them again.

The hardest part of this entire repair was locating the right socket and explaining why/how I burned my fingers (yes I had to touch the element to prove to myself it was that easy to fix and worked). 4 screws, 1 replacement part 5 minutes no cussing. This was the easiest repair I have ever done.

remove 2 screws holding element to oven back wall/ unscrew wires from element/ new element install the reverse of removal

First turned off the circuit that controlled the power to the Stove/Oven.
Then I removed the screws that hold the element in place.
I pulled the element out a few inches and disconnected the wires.
I attached the wires for the new element.
I replaced the screws.
I turned on the circuit.

And to reward myself baked a Coffee Cake. Yum!

Removed 2 screws with nutdriver.Pulled element out to expose wiring and disconnect 2 wires also with nutdriver. Reverse process. Unit reaired.

removed the old heating element which had about two screws and two connecting wires and replaced it with the new one. I twas so fast and easy. I thought I was going to need a new Oven!!!!!Thank goodness for your website!!!!!

If the bottom heating element is not glowing red when you turn the oven on replacing this part may be the answer. Look for a spot on the old element that could indicate it has shorted out and no longer carries a charge.
Very simple to remove the two screws holding the element in place, pull the element out about 3 inches, disconnect the two wires, replace with the new element and reattach the two screws. Simple and effective. The new element is fast and responsive. Do this before any other suggestions to replace more complicated parts in the thermostate etc.

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.

First, turn off the power. Remove the two retaining screws, pull out the broken element far enough to unscrew the connectors, remove the element, reconnect the new element, screw it back in, turn the power back on. Yes, it is that easy! Took me all of five minutes. Took longer to find my tools!

First I removed the 2 mounting screws that mount the element to the back wall in the oven, then pulled the element out about 4 to 5 inches, then removed the 2 screws attaching the wires to the element, then reversed the process to instal the new element. The only tool reguired was a 1/4 inch nut driver. Did the job in about 5 Minutes. The replacement fit and works perfectly.

I was lucky to look at other repair stories because I forgot to turn off the power!!! Nothing happen to me, but it was as simple as everybody else said. Unscrew the two screws, pull out element, unscrew another two screws and put back together in reverse order. Viola, the oven was back in working order just in time for a major event the next day. Thanks everybody for their tips and partselect for fast shipping.