JKP38G1J5 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Betty from Salem, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bottom Heating element broke
Ordered the part on Fri. AM and it arrived Sat. PM! Could not believe how quickly it arrived. Husband replaced the old element and I am baking again! Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from Centennial, CO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out element
Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Millbrae, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Heating element corroded.
I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- c from Cincinnati, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element melted! Lucky it didn't start a fire!
The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Dallas, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The element in the upper oven burned out. Looked like a welder's torch when it went out.
After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.
The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
My part was delivered in 2 days regular UPS.
The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William M. from Towaco, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element went dead
Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOE from WESTON, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned Out Lower Heating Element
Unscrewed the old one and screwed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Sugar Land, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes
Reversed the process to install the new coil.
Done in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from two rivers, WI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
oven wouldn't heat eliment was burnt and sparking
took out old then put in knew
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Stone Mountain, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower heat element died in our 30+ yr old oven
IT was fast and easy! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from West Springfield, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burned out bake element
The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Venice, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replace Burned-out oven bake element
Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven bake element broken
Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Gualala,Ca, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old burner had burned out and broken
removed old element and installed new, and oven is up and working like new
Was this instruction helpful to you?
Thank you for voting!