JKP18G4K3 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and made sure that there was no power feeding the element. Next I disconnected the two wires that power the element. I then removed the old element and replaced it with the new element. Tightened the screws but had to be careful on the second one and hold with plier as the first one bent a little as it was being tightened. Slid the element back after the connection screws were tightened and tightened the mounting screws. Reenergized and tested. The job went well - easier than expected...

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

Took the old one out and replaced with the new one. It was just awkward to get at.

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!

husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.

Throughout, I took care to not rest my full weight on oven door, although it's hard to work with arms extended. Shut off power to oven at outside circuit breaker, removed both racks, placed trouble light on open oven door at left to illuminate back of oven. Tilted element up to get at bolts. Used 1/4" socket set to remove two hex bolts holding burned-out element's plate to back of oven, pulled it out 3" to expose wire connectors. Held connectors still with pliers in left hand (to not bend wires) while loosening/removing connector bolts with socket set in right hand. Took effort to loosen. Removed element. Wiped oven floor clean. Positioned new bake element in same place, again held connectors still with pliers (left hand) and tightened wire connector bolts with socket set (right hand), pushed element back to original element's position. New element came with screws, not bolts, so used magnetic Philips screwdriver to get screws lined up (tricky), tighten new element's plate to oven's back wall. Removed trouble light, restored power, set closed oven for "bake" and "350 degrees." Element glowed hot in 1 1/2 minutes, ta-daah!

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole expierence.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.

Cut the power off to the oven. Removed both of the racks in the oven. Removed the 2 screws that hold each element in place. Pulled the bake element out as far as it would go and unscrewed the two wires. Then did the same for the broil element. It has a guard to keep it from dropping down and I had to remove that. The broil element is a little more difficult to remove but i had read that in the previous users writeups. Overall it was a great experience from a price, delivery and installation process.

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks