JBV42G304 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Albert R from Richmond, MO
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a burned out calrod unit
Simply unplugged the burned out one and plugged in the new one. It worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from San Andreas, CA
- Parts Used:
- WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original trim ring did not fit
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ella from Tampa, FL
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pre 1992 6" plug in electric cooking elements- rusted out
Worked, don't have to replace an old GE combination range "Microwave Cooking Center" when the surface units rusted out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Littleton, MA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element failed
lift up to 45 degree angle and pull towards you. This one went bad and the contacts welded themselves together. Took some shifting and tugging to free it. Normally, they slide in and out effortlessly, like any plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from cincinnati, OH
- Parts Used:
- WB1X5508
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
broken nylon retention pin in upper oven door
Removed 3 lower screws holding the upper oven inside door panel to the door frame. There is enough flexibility in the panel to coax it away from the frame at least an inch. Removed the old nut plate from inside the door and replaced it with the new one. Screwed in the retention pin and 2 washers while holding the nut in place. Assembled the 3 lower screws to complete the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!