JHC56G4D1 General Electric Range - Instructions

Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.

Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New element came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.

Unplugged bad surface element and plugged in replacement.

The Surface Element on our GE stove made in the mid 70's finally gave up and would not heat. I went to several of the big home improvement stove with not luck in finding the right heating element for our stove so I turned to a local appliance stove that carries GE products, they did sell me an element and asured me it was the correct one, but once again the element was the wrong one. Then with a simple google search for GE replacment parts I found partselect.com. With the detailed description and images with measuring grids I was able to quickly find the correct heating element for me stove. I am very pleased and the stove is back to 100%.
Thanks partselect.com

The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!

Made sure oven was turned off. I used nut driver to remove nuts holding old element to back of oven. gently pulled element out of wall, taking care not to yank because of wires attached to back of element. Made sure oven was off again and then used nut driver to carefully remove wire leads from receptors on element. removed old element from oven and got the new element. carefully used nut driver to attach wire leads to new element. When snugging the bolts to leads, used pliers to keep leads on the element from bending. carefully replaced wires and rear of element into the space behind oven, and used nut driver to attach the back of element to the back of oven. shut oven and turned on to make sure it worked. it did. I was very pleased with my experience with part select dot com, and will be buying another element soon to replace the one in my other oven! Thank you

Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.

The terminal blocks become brittle and carbonized with age resulting in very poor contact with the electric burners. The burners lose capacity to heat fully and eventually stop working.

Unplug the stove first! There is a risk of dangerous electrical shock if the power is not disconnected.

Repair involves removing the burner and the drip cup to expose the terminal block. Remove one screw on top to detach the block from the stove top. Remove the insulating cover and the clip that holds it in place on the back of the block. Detatch the two wires. At this point the age and brittleness of the blocks became apparent as they crumbled in my hand while removing the terminal screws. One screw had several layers of carbonization covering it and required needle nose pliers to get a firm grip in order to loosen it.

Inspect the wires to make sure there are no holes or cracks in the insulation.

Attach the wires to the new terminal block using the new screws provided. The new kit also included quick lock screw fastener clips to place over the holes in the stove top. It's a good idea to use these for more secure mounting and better grounding. Place the new terminal block under the stove top and mount it with the new screw provided. I had to unbend the mounting clip slightly to get it to fit, but it was easy enough to do with bare fingers.

Replace the drip pan and the burner. Plug the stove back in.

A pot of water now boils in under a minute compared to the 5 to 10 minutes it used to take.

Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewall and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!

Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.

I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct part shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.

Removed the old drip pans and put the new ones in.

Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.

I put new element in, reconnected two leads, replace two hex nuts and was done.

Turn off power to stove at circuit breaker before starting.

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I removed the old element from the oven and replaced it with the new element. Then I connected the two wires to the new element and pushed the element into place. Then I replaced the two screws that held the element in place. I then tested the oven and it worked wonderfully.

This was so easy to do. First I took the two screws out of the holding plate. Then the element comes out and I took the two screws attaching the wires to each end of the element out. To replace it just reverse the above and turn it on let it heat for about 10 mins to burn off any residue and you are ready to start baking again. Although not really necessary it is reccommended to unplug or turn of the breaker before you start working on the problem.