Models > JM950R5 > Instructions

JM950R5 General Electric Range - Instructions

Jump to:

All Instructions for the JM950R5
91 - 105 of 391
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Rand from San Mateo, CA
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
burned out lower heating element
Very simple 4 screws/nuts ...off on...done.
Best part was that I ordered the part regular shipping on a Sunday. Monday was a holiday...the part was at my doorstep at 8AM Tuesday morning. Wow that's service.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from McConnells, SC
Parts Used:
WB31X5014, WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old and corrosive due to age
After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from emden, MO
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bottom unit in oven was burnt out
removed 4 screws and exchanged units put the 4 screws back in. about 10 min.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karl from Kempner, TX
Parts Used:
WB32X10013, WB32X10012
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rachel from Stone Mountain, GA
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Lower heat element died in our 30+ yr old oven
IT was fast and easy! Thanks
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
steven from peabody, MA
Parts Used:
WB32X10013, WB32X10012, WB31X5014, WB31X5013
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
replacing old rusted drip pans w/ rings
simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Helen from Sacramento, CA
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
The bake element burned out and broke.
It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Dallas, TX
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Old bake element bubbled up, died.
Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
c from Cincinnati, OH
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Bake element melted! Lucky it didn't start a fire!
The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.

If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keith from Wauwatosa, AL
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
Old element burned out
Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Dallas, TX
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
The element in the upper oven burned out. Looked like a welder's torch when it went out.
After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.

The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Felicia from Little Rock, AR
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The bottom heating element in the oven was not heating
First I shut off power to oven. Then I removed two screws from the back of the oven. Pulled elemeent out a couple of inches and diconnected from the power source. I removed the old unit and replaced it with the new one. Connected it to power source. Pushed element back into place and replaced the screws. Turn the power back on and turned on the oven. ....And there was HEAT!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Lewisville, TX
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake element burned out.
I removed the two screws that hold the element in place; pulled the element out, disconnected the two wires held on by screws, replaced the element with a new one and reversed the procedure.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ron from Flower Mound, TX
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Beke Element broke into 3 pieces
followed the existing guidelines from this site.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michelle from Pasadena, TX
Parts Used:
WB44X200
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Heating element broke in several places
Turned off the power source to the oven. I then removed the two screws that hold the element in place, then pulled the element out about 3 inches and disconnected the two wires at the back. The hardest part was getting the screws turned to connect the new wires at the back.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JM950R5
91 - 105 of 391