JB400G*H2 General Electric Range - Instructions

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

Drilled out the screw on one wire as it was corroded to the metal socket. Sanded both wire terminations. Installed wires into terminal block. Reassembled all loose parts and installed into burner slot. Worked perfectly.

Unplugged stove, removed front door, carefully removed two screws holding the cover plate of the element. Gently pulled the element out about 3-4 inches removed the two screw attaching the electrical wires to the element , making sure the wires did not pull back into the stove. Removed old element, attached new element to the electrical wires with the new screws received with the new element. Carefully pushed the wires and element back into place making sure the insulation was also in place. Re-attached the cover plate with the two screws I had removed. Plugged the stove back in and tested the element. Replaced the front door .... job complete!

Just wanted to add that the part came in two days, super mailing time, thanks!!

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

I removed the 2 screws and the 2 wires from the broken heating element. I removed the broken oven heating element. Then I attached the 2 wires to the new heating element and put the 2 screws in to attach the new heating element into the oven. The new oven heating element worked just fine and I was done.

First I turned off the circuit breaker leading to the oven. Then I removed the two screws that held the old element in place. I pulled out the element and disconnected the wires. I reconnected the wires to the new element and pushed it back in place. I then secured it with the two screws. I turned the circuit breaker back on and turned on the oven. Works just great!!!

remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in

Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my finger to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

Ordered part, took old bake element out, installed new bake element. It was real easy.