1J2442M2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- brian from temple, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
burned/blow out element
pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyler from Dannemora, NY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt out
Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from La Grange, MO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lower heating element burned out
I replaced the element. The new part arrived within 48 hours of being ordered. It worked. The part that sticks out the back of the oven with the connections was a little shorter on the new element which made it more difficult to put the wires on but it was not too difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Brighton, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element broken
Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Beckley, WV
- Parts Used:
- WB30X354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
one element suffered a small puncture where the heated element burned thru
The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milt from Manchester, CT
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
bake element burned out
A socket set was used to remove the old element. New element was installed with a slotted screw driver and socket set. It took 15 minutes from start to finish to complete the removal and installation. Element tested OK. The bake elment was delivered overnite by Fedx.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from Delray Beach, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
heating element in oven burned out
--ordered part on line ---It came in the next day without any extra charges for over night shipping! The whole thing with shipping was about $26 and so easy to install. Turned of circuit breaker, unscrewed element and screwed in new one.I was so impressed with 'Part Select'. I have never had a more efficient and inexpensive experience with online shopping. Thank you , I would highly recommed you to everyone! Dee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Nashville, TN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out, oven would not get hot
Turned off breaker for oven, removed baking (lower) element, searched website to match up size, shape, and connector-type of replacement part. Placed order and received two days later. Mounted new part in 10 minutes, turned on breaker, and immediately baked fries for children. No problem. Much cheaper and easier than replacing entire built-in oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eunice from North Providence, RI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broken bake element
1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from VACAVILLE, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out lower element
Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Anderson, SC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
original bottom heating element melted down into wall
Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement part here in 4 days at new years. Part was only $18.45. Parts Select rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Cody, WY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element broken and bubbled
removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from minneapolis, MN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
element was broken
replace old one with new one thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jacksonville, OR
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Very low oven heat
Ordered new element (super-easy to select the right one at this site!). Turned off stove breakers. Removed two screws holding mounting hinge plate with nutdriver. Detached wires with regular screwdriver. Attached wires to new element lugs with screwdriver, using furnished new screws. Reinstalled element hinged mounting plate with screws and nutdriver. Only difficulty is 1) working bent over inside the oven because the wires are short, and 2) wire screws are regular, not Philips, with shallow slots so screwdriver slips out frequently.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hubert from Oak Ridge, TN
- Parts Used:
- WB30X356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
A plastic bowl was placed on the hot eye and melted.
The old eye was lifted up, hinge screw removed, and three screws removed from the eye that connected lines to it. Did just opposite for installation. Very easy. The hardest problem was finding an eye with three screw-type connections.
Was this instruction helpful to you?
Thank you for voting!