JD14Y1 General Electric Range - Instructions

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the element with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.

I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)

That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires

removed it, ordered it and it only took 15 minutes to replace it.

I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.

Very quick delivery, within 3 days.

I removed the two screws that hold the element to the back of the oven. Pulling the element out of the back, I removed the screws which connect the element to the electrical wiring. I placed the new element into position and reconnected the wiring. I made sure that the wiring and connectors were insulated with shrink wrap plastic, then pushed the new element into place. Connecting the two screws to the back of the oven completed the job. Toughest part, kneeling on my knees -- the part supplied fit like a glove and it works wonderfully well. Hint: measure the connectors to the wiring so that you order the correct length! (I didn't and had to reorder, but I am very happy with PartSelect.)

First of all the part came super fast with standard delivery. We threw the circuit switch to the oven. We used a nut driver to remove the nuts holding the element in place and then gently pulled it out of the hole so we could see the terminals. Using a screwdriver we loosened the screws that hold the terminals to the power lines. We put the old element aside and laid the new element on the floor of the oven. Using a screwdriver and the original screws we attached the terminals of the new element to the power lines. Using a screwdriver and the new screws provided we attached the bracket to the back of the oven. Turned on the power; used the oven. Works perfectly.

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.