J317Y1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Warr Acres, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The bottom heating element was not working
This is a forty five year old oven. It was only four screws and it was done. The new part works like a champ! This save me from buying a $800.00 replacement. I removed the two 1/4 screws holding the element to the back of the oven and then took the flat head screws loose from the terminals on the old element. I then put everything back as it came out; took less than 5 minutes and the part arrived overnight! Thank you again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from stuarts draft, VA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bad element
first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from San Antonio, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old drip pans rusted out.
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from STREATOR, IL
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element was not heating
I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from temple, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
burned/blow out element
pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing bake element
Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from San Jose, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed new Drip Pans
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tamaqua, PA
- Parts Used:
- WB30X356
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
The burner only heated half of the coils
The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from minneapolis, MN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
element was broken
replace old one with new one thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eunice from North Providence, RI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broken bake element
1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from VACAVILLE, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out lower element
Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Anderson, SC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
original bottom heating element melted down into wall
Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement part here in 4 days at new years. Part was only $18.45. Parts Select rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Cody, WY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element broken and bubbled
removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter J from Oceanside, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old stained drip bowls
I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyler from Dannemora, NY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt out
Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!
Was this instruction helpful to you?
Thank you for voting!