JGB915BEF2CC General Electric Range - Instructions

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.

Took top off, removed wires from old spark module and put them on new one. Very easy and quick, works very well now.

Replaced old with new.

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

slid the old ones out and slid the new ones in. done

Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.

First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.

With the model number I wnet on Parts select site and located the part through the problem finder selection,(GREATFEATURE!) (74% the problem is the Flat Style Oven Igniter) (watched the video on installation and compared my unit with the one in the video). The video explained installation completely and made it very simple. The only critic is that the oven door can be removed completely to make it easier to get in the the oven, opening part way and lifting up the oven door will come completely off. Also the broiler pan drawer can be taken completely out if you would need to get in this way for some reason. Final note: I called the local GE dealer Parts dept- they would have had to order the part anyway and it would have cost three times what Parts Select charged me.Save $$$ great! .

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

Very was ti replace racks and knobs. Very fast mail service

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.