J303*01 General Electric Range - Instructions

I removed the two screws that hold the element to the back of the oven. Pulling the element out of the back, I removed the screws which connect the element to the electrical wiring. I placed the new element into position and reconnected the wiring. I made sure that the wiring and connectors were insulated with shrink wrap plastic, then pushed the new element into place. Connecting the two screws to the back of the oven completed the job. Toughest part, kneeling on my knees -- the part supplied fit like a glove and it works wonderfully well. Hint: measure the connectors to the wiring so that you order the correct length! (I didn't and had to reorder, but I am very happy with PartSelect.)

First of all the part came super fast with standard delivery. We threw the circuit switch to the oven. We used a nut driver to remove the nuts holding the element in place and then gently pulled it out of the hole so we could see the terminals. Using a screwdriver we loosened the screws that hold the terminals to the power lines. We put the old element aside and laid the new element on the floor of the oven. Using a screwdriver and the original screws we attached the terminals of the new element to the power lines. Using a screwdriver and the new screws provided we attached the bracket to the back of the oven. Turned on the power; used the oven. Works perfectly.

Super easy, 1 2 3 steps and your done. Make sure to turn power off, remove two screws off of back plate. Remove two screws on wire connectors. Throw old element away and connect both wires to new element and screw back into place. Turn power back on and start cooking.

very easy--cut power supply 2 screws then 2 more on element quick and easy

Removed element and installed new element. Fit perfect, no problems.

Unscrewed four screws, removed old element, replaced with new part, done!

I took the old element out, compared it to the pictures of the GE replacement elements, identified the correct one and ordered. It came I installed it in 15 minutes and it works just right. I was unable to determine the model number of my old oven so the pictures of replacement elements were invaluable. Thanks for making it so easy to avoid calling a repairman.

The repair seemed very easy, even before I attempted it. When I recieved my part it was very obvoius that this was my problem part. The old element was worn out(21 yrs old). Having Thanksgiving around the corner, my wife was happy we had a fix to our not ready to replace oven. I was very pleased with your website picture matching choices and the very fast shipping you offered.
Thank You RR from Massachusetts

Removed the panel screws that hold the bake element to the back of the stove. Then I disconnected the old element from the wires. Attached the new element using the provided screws. Reattached the old panel screws to hold the new bake element in place. Works great.

The new bake element doesn't have an item number on it, so I kept the old element in a cabinet someplace in case I have to replace this one again some day. I've lost the model number for my very old GE wall oven, so without that item number I'll be in trouble.

I double checked to make sure I got the right part.I looked at your video and then just did as you suggested. It was a easy fifteen minute job. Thank you for making this so simple to follow along with.

Turn off breaker for unit! Use nut driver to remove old element,and replace

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

Remove the old element by removing one screw and inserted new element and replaced the screw.

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.