JC28Y1 General Electric Range - Instructions

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.

I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)

That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

I disconnected the 240 volt supply by removing the fuses from the fuse panel. Next I removed two screws that hold the element in place with a nutdriver. Then being careful not to short or ground the wires I pulled the element out 3 or 4 inches and turned the oven control to the on position and tested for voltage, line to line then each line to ground to be sure the correct fuses were pulled. Turned the controls back to off. Next I disconnected the wires using the same nutdriver and removed the old element.
I placed the new element in the oven, attached the wires using a screwdriver backing it up with pliers to hold the connector on the element, then slid the element into position and installed the two screws in the back of the oven, then reinstalled the fuses.
Partselect shipped the order right away. I ordered Thursday evening and received the element Monday morning using standard shipping. I wasn't able to reference the oven by part number (it is a 40 year old GE oven) but their pictures and 1" grid made it convenient to pick the correct part.
In the past I bought the main control circuitboard for my Kenmore dishwasher, a door light switch for my refigerator, a turntable motor for my GE microwave vent hood, and an element for a Maytag oven. Every time I have ordered parts they were in stock as indicated and shipped right away and were the right part.

I have to tell you i got wrong partfirst it was my mistake I got on phone and the lady understood my problem and told me procedure of returning part I got the right partnext day. I watched the video on how to do the job,although O new how. The video was a wee bit off,from what was easy.The man doing the talk through repair showed detaching the connections and bending each one back s as to not go back inside there inclosure. The connectors were way short on this one .The only way to attach the element was to take off back cover and push them together back there. Took couple extra minutes ,but job don e Ps will be ordering something soon

Removed the oven shelves. Removed two small screws in back of oven. Gently pulled out element to get to two other small screws connecting the element and removed them. Removed old element. Placed new element in oven connected the two screws to the element. Replaced two screws on back of oven. Replaced the shelves. That's all there was to it.

Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding element in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks

My husband did the repair in about 15 minutes. It was apparently self explanatory and required no directions. Take the old one out and replace it the same way it came out. And viola!!, the oven works like new - all for about $33. Thanks

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above