JHP56V4K4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES from LEBANON, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Something Had Dripped Down On The Baking Element Causing It To Over Heat In One Spot And Short Out.
This was so easy to do. First I took the two screws out of the holding plate. Then the element comes out and I took the two screws attaching the wires to each end of the element out. To replace it just reverse the above and turn it on let it heat for about 10 mins to burn off any residue and you are ready to start baking again. Although not really necessary it is reccommended to unplug or turn of the breaker before you start working on the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Golden, CO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The heating element in the oven failed, after at least 16 years of good service.
First, we turned off power to the range. We removed the screws holding the element to the back wall of the oven and pulled out the element a few inches. We disconnected the 2 wires from the old element, and attached the new element with the 2 provided screws. We pushed the element back into the wall and secured it with the screws. Turned the power back on, turned the stove back on and, voila, the frozen pizza was well on its way to becoming dinner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr Sal from Eastampton, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
element wont heat up
4 screws 4 off then 4 on done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from FOUNTAIN, CO
- Parts Used:
- WB17X5113
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Terminal block wire had burned out
Unplugged the range. Opened the range top, unscrewed the old block and cut the wires back. New mount did not match the range top. Removed the old mount from the old terminal block and removed the new mount from the new terminal block and inserted the new block in the old mount. Spliced the wires with the provided wire nuts, protected the splice with the provided heat shrink tubing and installed the burner in the new terminal block. Reinstalled the power cord and tested the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FALL RIVER, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bottom oven heating element was out
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marian from Inglis, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No heat on bake.
The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terri from Edgewater, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Took forever to preheat
When I told my husband I ordered the part and was going to fix it myself, he laughed and said I might not have ordered the right part for the problem and I should just buy a new stove.
The part was delivered the day before Christmas, just 3 days after I placed the order! I had read the stories of others fixing theirs and gave it a shot. It took me longer to find the tools then it did to replace the element!
I took the screws out , pulled the element toward me and disconnected the wires. Put it back the way I found it. Oven heated up in less then 5 minutes!
The part was delivered the day before Christmas, just 3 days after I placed the order! I had read the stories of others fixing theirs and gave it a shot. It took me longer to find the tools then it did to replace the element!
I took the screws out , pulled the element toward me and disconnected the wires. Put it back the way I found it. Oven heated up in less then 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Deer Park, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
element went out on oven
Made sure oven was turned off. I used nut driver to remove nuts holding old element to back of oven. gently pulled element out of wall, taking care not to yank because of wires attached to back of element. Made sure oven was off again and then used nut driver to carefully remove wire leads from receptors on element. removed old element from oven and got the new element. carefully used nut driver to attach wire leads to new element. When snugging the bolts to leads, used pliers to keep leads on the element from bending. carefully replaced wires and rear of element into the space behind oven, and used nut driver to attach the back of element to the back of oven. shut oven and turned on to make sure it worked. it did. I was very pleased with my experience with part select dot com, and will be buying another element soon to replace the one in my other oven! Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Harvard, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven wouldn't heat because coil had burned through
The part was delivered in 24 hours with regular
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shannon from Birmingham, AL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Baking element went out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the old piece and connected the wires to the new piece. I'm a woman and this took me less that 15 minutes to complete. Easy as pie. On top of that, I received my order within 3 days! Very impressive, PartSelect. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from New Lebanon, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
bake element disintegrated
At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vittorio from MATAWAN, NJ
- Parts Used:
- WB44X139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Old broil element was shorted out.
Unscrewed the 2 screws holding the old one in and the 2 bolts holding the bracket. Installed the new one in. 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from buckhannon, WV
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
bake element no heat
took old element out , put new element in.very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from CHESHIRE, CT
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Element burned out
My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Bend, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The small element blew out consequently shorting out the infinite switch.
The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
Was this instruction helpful to you?
Thank you for voting!