JDP39WKW General Electric Range - Instructions

Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

Removed old element with a socket wrench. Replaced new element with socket wrench. Pretty easy!

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Removed element. Ordered new one. Installed it.

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

Unplug the stove. Remover back panel. Remove coil and pan. LIft stove top. Remove screw(s) holding element in place and follow wires to the back of the stove and disconnect. Replace with new kit. Easy.

This is the second time the unit has gone bad. None of the other three burners has ever had the problem.

Thanks for having the part available.

I pulled off the back panel and the two wires were attached to the back of the know for the burner that did not work. I unhooked the wires, fed the new ones into the same slot and clipped the block in place. That was it!

Prior repair job had spliced the terminal block wires with electrical tape; electrical tape caught fire while making pasta.

anyways, disconnect all power, remove burners, pull stove out. you'll need a 1/4" drive socket to get the back cover off; six bolts total. phillips head screw driver to unscrew the terminal blocks; replace with new terminal blocks; it did not seem to matter which wire plugged into the back. put everything back together. very easy.

standard procedure, very simple

Simple job. Disconnected the power to the oven, removed the two screws holding the old lower element, pulled it out and disconnected the two electrical wires. Installed the new one by simply reversing the removal process. Very impressed with PartSelect on price and delivery. My local repair company wanted to charge me twice the price and a part delivery time three times longer. Will definitely use PS in future

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Used a nut driver to remove element the insulation was tight and pulled the wires off before they came out of the oven. I made a small hook out of a coat hanger and pulled the wires through the opening.