JKP18G4K1 General Electric Range - Instructions

On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed. Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

Took the old one out and replaced with the new one. It was just awkward to get at.

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!

husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

I read your website repair testimonials by previous customers and used that advise to do the job. I liked the suggestion to use something to attach to the unattached wires so they don't slip back into the unit. I used two clothespins. I had one stubborn electrical connection to disconnect so it took a little longer -about 30 minutes. But it was a simple job to do and my oven works fine again. The item was delivered timely from the order date and packaged well. Thank-you!

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

Throughout, I took care to not rest my full weight on oven door, although it's hard to work with arms extended. Shut off power to oven at outside circuit breaker, removed both racks, placed trouble light on open oven door at left to illuminate back of oven. Tilted element up to get at bolts. Used 1/4" socket set to remove two hex bolts holding burned-out element's plate to back of oven, pulled it out 3" to expose wire connectors. Held connectors still with pliers in left hand (to not bend wires) while loosening/removing connector bolts with socket set in right hand. Took effort to loosen. Removed element. Wiped oven floor clean. Positioned new bake element in same place, again held connectors still with pliers (left hand) and tightened wire connector bolts with socket set (right hand), pushed element back to original element's position. New element came with screws, not bolts, so used magnetic Philips screwdriver to get screws lined up (tricky), tighten new element's plate to oven's back wall. Removed trouble light, restored power, set closed oven for "bake" and "350 degrees." Element glowed hot in 1 1/2 minutes, ta-daah!

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole expierence.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

Replacing the electric oven element was easy. It took about 20 minutes and all you need is a screwdriver and a pair of pliers. What you have to do first, turn the power to the oven OFF. Remove the original element carefully observing how
it was installed and install the new element in the same order.
I have used Parts Select a couple of times in the past years and the delivery came quicly without any problems.

Spyro.

First I turned the power off to the oven. Then I tried to take out the nuts holding in the element. One nut came off easily, the other one was rusted on, I had to use wd40 to loosen it. The project was easy once I got that nut off. I pulled out the element, which is connected to two wires. I took those screws out, connected the new element to the wires, re-attached the screws, pushed it back in, attached the nuts that hold the element in the oven. Then I turned the power back on and the oven works like a charm. I installed it the day I got it. I was surprised how quickly it was shipped to my house. I am so glad I repaired the oven, a new one would have cost over $800, I bought the element for less than $30, including shipping! It also sets a good example for my daughter. It taught her that her mom can repair things too, it's not just something men can do!