JB988KK2CC General Electric Range - Instructions

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

It is first necessary to remove the door from the range according to the manufacturer's instructions. Once removed, lay it down on a flat, protected surface with the outside facing down. Remove the two upper phillips screws and the hex nuts on the bottom channel. Next, separate the inside panel from the outside panel. You will then see the remaining hex nuts that have to be removed in order to replace either the bottom trim channel or the side pieces.

#1 loose two screws and lift up the cook top; #2 disconnect the burner coils by unplugging three connectors; #3 disconnect the switch attached to the burner by unplugging three connectors; #4 loose two screws to unmount the burner; #5 do the reverse to mount/connect the burner, and close the cook top.

very easy, door comes off without any tools. youtube has instruction for that. seperate the innerdoor pannel to access the screws for the trim.6 screws holding the trim. the hardest part was cleaning the rust off.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

Pretty easy. Pull oven out from wall and un-plug. Open oven door and look up. Find two small sheet metal screws and remove. Remove two retainer clips, un-plug triple haliant element and install new part. Re-install retainer clips, replace screws and you are done.

opened the oven door an took 2 screws out that hold the stove top down. lifted an propted it up an replaced the burner. pretty simple job just plug the wires in just like the old burner

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Followed the instructions that were sent to me by E-Mail.

plug in thermistor when needed

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Added 2 new clips and installed the burner