JBP91KF1CC General Electric Range - Instructions

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not slide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.

On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,

pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range in palce and done.

removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.

First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. This was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.

Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success

My friend's husband came over to help. I mentioned that after unscrewing the old bake assembly unit, we would have to capture the wires or they would slip into the back. Before he even had the screws undone, the wires did, indeed, slip into the back. He then removed the back panel and retrieved the wires, pushed them back through the insulation and clipped each of them onto the back assembly. However, the wire clips kept slipping off so he eventually had to criimp the clips to keep them tight on the ends of the bake assembly. That troubled me; what if in the future one of those clips comes loose while the oven is in use? Any suggestions on how to keep these connectors on tightly?

The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

unscrew and disconnect the old unit. Connect and screw in the new unit

Had to remove rear cover to connect wires, removing them from the front caused the wires to fall into rear.