JMP28GR3AD General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Beverly from Baton Rouge, LA
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Burned out broil element
.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frederick from kingwood, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element burnt through
Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Maitland, FL
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
bake element burned out
removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Arvada, CO
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating element in bottom oven burned out
First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KY from Lenapah, OK
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven would not heat
Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Crescent City, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out surface element
simply by inserting new replacement into electrical socket ...very satisfied in new replacement price and quick delivery date Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Coto de Caza, CA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking Element wouldn't heat but the broiler worked fine.
First I turned off the power at the fuse box, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced with the new element. Very Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from New Berlin, WI
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element didn't heat. Cracked.
I simply pulled out the old element. Plugged in
the replacement, which arrived very quickly, and
that was it. I couldn't believe that was all there
was to it. I really loved being able to order the
replacement part online. Intend to order more
replacement parts just to have my stovetop
looking like new again.
the replacement, which arrived very quickly, and
that was it. I couldn't believe that was all there
was to it. I really loved being able to order the
replacement part online. Intend to order more
replacement parts just to have my stovetop
looking like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Richmond, VA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new electric element
A breeze! Part was perfect replacement, snapped in place without tools, and heated almost immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Charlotte, NC
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
broken element
turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Avon, OH
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic canister melted on burner
just plugged it into the socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni Ann from Manalapan, NJ
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The baking element broke.
Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur E. from St. Louis, MO
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I ruined old unit
Removed old, and replaced with new, heating element! Maybe 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Dallas, GA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner not working.
I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from DULUTH, MN
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I Ruined My Burner -- This Was A Solution For Me...
I simply pushed the new burner into hardware. I then tested it to see if it works. . .
Was this instruction helpful to you?
Thank you for voting!