PC2S920SEF4SS General Electric Range - Instructions

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

I removed oven door so i could reach easier. Then removed screws from Broiler element at the back of the oven. Pulled off connected wires. Slid wire connectors on new element and screwed bracket in.

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

Performed repair using a video for reference.

First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.

Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY

I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.

All burners have been working perfectly since the fix.

Order parts and installed - no tools needed - completed repairs less than 1 minute

I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.

I JUST EXCHANGED THE BURNER AND BURNER CAP.

When this happens the plunger switch has to be replaced. This is a small plug like piece that has 4 plug in wires.

So you first unplug the range from the wall outlet. Then remove the oven door off the hinges ( see owners manual for removal ) then you take the right side panel off and there you will see the plunger switch. Before removing the old switch make sure you plug the new one in exactly like the old one. I laid the old one next to the new one and plug them in one at a time. Its a little tricky unplugging them . After a few tries I figured it out. You have to use your thumb and finger and press and pull up by where the wire plugs in. Before putting back together you may want to test the new switch. Plug range back in wall outlet push the black piece that sticks out from switch and if the oven light goes out its fixed. Unplug from wall while reassembling side panel and door. I can say this do it yourself saves a lot of money not having a repairman fix it.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.