15428-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- brendan from lebanon, NH
- Parts Used:
- WB17T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Baker from Durant, OK
- Parts Used:
- WB15K5076
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The door handle on the over was broken.
I removed the oven door from the range. Removed the broken handle and replaced the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wiscasset, ME
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Door handle end cap got brittle and broke on oven door.
Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Canyon City, CO
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The burner bowls were encrusted with grease and spills.
I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.
Was this instruction helpful to you?
Thank you for voting!
Stove door handle broken
Unscrewed the old broken pieces to the handle and put on the new handle, very easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from South Bend, WA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.
The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Cogan Station, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken oven door handle. Needed the brackets and screws to repair it.
removed the broken parts and screwed on the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Milan, TN
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken door handle
Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Mars, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
End cap plastic broke at screw entry
Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cornelius from Hollister, CA
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
plastic sockets in end caps for connection screws broke off
Very detailed repair instructions on internet made installation of new end caps a job not needing a professioal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Schererville, IN
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
broken door handle
repair was easy and the video was very good. My only problem, I had to go buy a tool, I did not have a nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Muskego, WI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke end cap while moving range
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this instruction helpful to you?
Thank you for voting!