JCBP78DP2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- bryan from cocoa, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from valentines, VA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
eye wouldnt come on
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Greensboro, GA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner not heating.
Isolated to control switch.
Replaced
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Mc Kees Rocks, PA
- Parts Used:
- WB08T10026, WB8K1, WB32K5, 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
light keep burning out in oven.
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Redding, CA
- Parts Used:
- WB23X5340
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
oven continued to get F2, F3 and F5 error messages when ovewn got hot
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Tombstone, AZ
- Parts Used:
- WB44K10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating Element Burned out
The task was very easy. After recieving the replacement I removed 2 small hex head screws using a nut driver. I pulled the slip on connectors apart the reversed the steps. I was done and able to use the oven in less than minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Granby, CT
- Parts Used:
- WB02K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic glide broke
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryl from Savannah, TN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bad control board
Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed oven back plate. Pluged oven in. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sun City West, AZ
- Parts Used:
- WB03T10282
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
prior knobs were discolored and ugly
just purchased new knobs. The price was great, just took a little longer to receive then anticipated though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!