GRCR3830ZSS-1 General Electric Range - Instructions

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

We ordered the part from Part Select, got it within a week and replaced the door.
It is a little tricky because one has to dismantle the entire door to do the repair (inside screw to undo).
You'd preferably be 2 to do the repair, although one can manage.

Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and position them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.

Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.

after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.

I removed the screws from the underside of the stovetop, lifted up the top, propped it up to keep it from falling (using a large book), and removed the old burner by unscrewing it from the top and removing the wire connections. I then screwed the new burner into the top, and attached the wires back to the burner, dropped the top down (gently and carefully, of course), and screwed the top back down to the rest of the stove. It was fairly quick and painless. Although, putting the stove back into his position was not easy, but that was no fault of the stove!!

Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Very easy to replace. So easy even a man can do it.

opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.

Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.

Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless