ECBP82SP1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tiffany from Lexington, OH
- Parts Used:
- WB30T10130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Outside portion of Element broken
First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from NEKOOSA, WI
- Parts Used:
- WB25T10041
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hot burner light lens broke off.
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Buckeye, AZ
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Loveland, CO
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
fried oven control using raid
replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Greensboro, GA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner not heating.
Isolated to control switch.
Replaced
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Mc Kees Rocks, PA
- Parts Used:
- WB08T10026, WB8K1, WB32K5, 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
light keep burning out in oven.
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryan from cocoa, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from valentines, VA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
eye wouldnt come on
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Sonoita, AZ
- Parts Used:
- WB27T10668
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Pilot light out
Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETE from MANCHACA, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Blew the electronic Control Board
It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from San Diego, CA
- Parts Used:
- WB24T10027
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Getting the right stove model number and part number
Difficulty was in determining the right model number and part number of a switch. Noted that the left front burner came on when the switch for the left back burner was turned on. By inspection I found the left front burner switch had become faulty by actually hearing an electric arc in the switch and smelling the oder in the switch. With help from the person I called I was able to determine that the Model Number on the actual stove was wrong. It had an extra 0 between the W and F which she said was a common error in the GE model number. I then gave the switch number I found on the switch to the contact person and she was able to verify the right part number. It was relatively easy to replace the switch by taking off the back upper plate then taking off two screws that held the switch to the stove. The part came quite quickly once ordered. Sears repair wanted $75 just to diagnose then the cost of the part. I got the switch for $69.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Daphne, AL
- Parts Used:
- WB27X45466
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven control panel was blacked out..no clock no start.
Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!