JCBS64DM1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Apex, NC
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the bake element broke
First I removed the 2 screws and removed the bake element, replaced the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from DECATUR, AL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Red Light On
Red Light Off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa M from denver, CO
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broiler not working
Turned off electricity. Removed two screws that held the element in back of oven. Removed the two screws that held it up to top of oven. Disconnected the two wires that held it in the rear of the oven. Removed it from the top support. Replaced the old element with the new in the support. plugged it it, replaced all four screws. Turned on the electricity and turned on the oven-it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina from EVERGREEN, CO
- Parts Used:
- WB35K10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Mice had destroyed the top of the insulation leaving dropping and shredding pad
I lifted the top of the range, pulled out old insulation (which was gross!), pulled out two wires (grounding, I think?) replaced with new insulation, reinserted wires and wahla! Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Bolton, MA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from LIBERTY HILL, TX
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven in accurate temp too low.
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Mt. Pleasant, MI
- Parts Used:
- WB15T10176
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broke oven door handle while unloadin new stove.
loosen interior panel of oven with star driver. Removed broken arm. install inner screw and then install final screw to both panels and handle.
The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.
Other than that it when smoothly.
The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.
Other than that it when smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Golden Valley, ND
- Parts Used:
- WB02K10158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer support broke.
Removed the screw from the broken piece and put the new piece on and put the screw on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Thornton, CO
- Parts Used:
- WB30X46986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out broiler element
Don't forget to unplug and/or turn off the main breaker!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lee from bethel, CT
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
change broiler element
removed 2 1/4in. drill screws holding broiler element to oven removed 2 1/4in.drill screws holding broiler element to top of oven removed female spade connectors ffom old element and reversed assembley very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Freeport, IL
- Parts Used:
- WB02K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I broke the left drawer glide on our oven
I unscrewed to old glide and replaced it then re attached the screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from AURORA, CO
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
GE oven showed "F2" error code and was over-heating
I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- abbas from redmond, WA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
surface burner switch was burned
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from CHANNELVIEW, TX
- Parts Used:
- WB24T10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace Surface Burner Switch
Unplug stove.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from BILLINGS, MT
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven Temp. went too high and the door locked. Burnt the food
This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.
Was this instruction helpful to you?
Thank you for voting!