JCBS64BK1BB General Electric Range - Instructions

Pull out wires & replace element by putting wires back in then tighten...done!!!!

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-standard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.

Easy

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

popped the new one on!

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.