Models > JCBP400DT2WW > Instructions

JCBP400DT2WW General Electric Range - Instructions

Jump to:

All Instructions for the JCBP400DT2WW
76 - 90 of 125
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
bryan from cocoa, FL
Parts Used:
WB24T10029
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roscoe G from ROCHESTER, NY
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
2 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jack from Greensboro, GA
Parts Used:
WB24T10029
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Burner not heating.
Isolated to control switch.

Replaced
1 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from Mc Kees Rocks, PA
Parts Used:
WB08T10026, WB8K1, WB32K5, 40A15
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
light keep burning out in oven.
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
2 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Edwardsville, IL
Parts Used:
WB23X5340
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Oven Sensor Replacement
The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BILLY from WEBSTER, FL
Parts Used:
WB24T10029
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Burner Would Not Turn Off
Replace control switch
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ralph from Redding, CA
Parts Used:
WB23X5340
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
oven continued to get F2, F3 and F5 error messages when ovewn got hot
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this instruction helpful to you?
Thank you for voting!
Customer:
brendan from lebanon, NH
Parts Used:
WB17T10011
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Winter Garden, FL
Parts Used:
WB24T10025
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Burner would not turn off
The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get the switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Albuquerque, NM
Parts Used:
WB02T10017
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Convection fan came loose from shaft
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from Chipley, FL
Parts Used:
WB24T10025
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench set
burners would go to full high heat& not reduce down.
Hubby did the job..all went well except for the arthritis & having to bend pull stove out from wall ,pushing back..ha-ha.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Monterey, TN
Parts Used:
WB08T10026
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
Customer:
loma from Neah Bay, WA
Parts Used:
WB02K10062
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Drawer glider broke about a year ago.
My wife could open and close the drawer without too much difficulty, but occasionally, it would not close properly and she would have to empty the contents do could alaign it properly to close. The last time she was talking about buying a whole new drawer. I asked her what the part looked like, as I never to fight with it. I went online and found the part for $1.16 plus shipping at $8 plus. It was well worth the time and effort, and I now have a happy wife. Paul Parker
Was this instruction helpful to you?
Thank you for voting!
Customer:
Creed from Topsham, ME
Parts Used:
WB24T10025
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set
Burner light would not go out.
Identified the switch that went bad. Order a new one and replaced it. The part came in a timely fashion and I am pleased with the result.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from Broadway, VA
Parts Used:
WB31T10015, WB31T10014
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
slot that heating element fits was worn down and caused burners to be uneven
replaced with new ones
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JCBP400DT2WW
76 - 90 of 125