JXDC440R2WHC General Electric Range - Instructions

I've been looking for an 8" replacement burner for my GE stove after my original burner caught on fire over a year ago. I had all but given up on finding a replacement after searching at all the stores in my area and also searching on the net. After cooking sides for Thanksgiving dinner this year and the pain of cooking with only 1 large burner, I decided to search again for a burner on line and thank goodness I found this site! All I did was put in the model number of my range/stove and the site directed me to the replacement burner. The picture of the burner looked like mine, so I decided to purchase it but I still wasn't convinced it would fit and work because of my failed previous burner purchases. I really thought my burner was too old and the part was no longer made. Well the part shipped very quickly and lo and behold it fit and worked! Installing was a breeze...I just snapped it in...thanks so much!

Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!

It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!

I simply pulled out the old element. Plugged in
the replacement, which arrived very quickly, and
that was it. I couldn't believe that was all there
was to it. I really loved being able to order the
replacement part online. Intend to order more
replacement parts just to have my stovetop
looking like new again.

It was as easy as you said. I took the back off, removed the screws holding the terminal, un-hooked it and put the new on on. Replaced the back and wa-la! Working burner

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

Removed the back cover with a socket tool, unplugged the old terminal and plugged in the new one. there is a screw holding the terminal block. so easy.

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

Pull out the range. Pull out the electric plug. Unfasten the back panel. Raise the range top. Replace the terminal block in exactly the same position as the old one. Put everything back.

This is the third time I have replaced it so it is very easy now. This time I spent a little more time making sure the burner element prongs were just just like the others. Must have been a little loose in the block.

Shut the power off and unscrewed facial hardware ,unplugged terminal and unscrewed hold down bracket and redid everything that I mentioned above. For a rookie it was a piece of cake.

Replacing the Surface Burner Terminal Block Kit was very easy.

1. Pull the stove from the wall a little so you can have space to work. I unplug the stove from lthe 220 outlet. Then remove the Surface Burner element.

2. Then we removed the back pannel from the stove by removing the screws with a nut driver. Only four screws to remove.

3. Once the pannel was removed. I Unpluged the wires from the stove pannel. Being careful not to damage the plug in. There were only two wires to unplug. So trace the wires to make sure you are unpluging the correct one.

4. Lift the top up on the stove and unscrewed the Terminal Block from the top of stove. We only have one screw there.

5. Pull the Terminal Block and wires out and replace with the new Terminal Block, making sure the wires were feed along the side under the top of stove so they can not be damaged. Plug in wires and replace pannel.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

The wire to the burners were old and needed replacement. When the new terminals arrived, my husband had gone hunting. When the parts arrived, I pulled the stove away from the wall and found the nut driver that I needed. I removed the screw on the terminal box under the burner and realized I had to remove the back panel of the stove. I unplugged the old wires and plugged in the new ones. I installed the new terminal boxes under the burners and plugged the burners back in. My stove works like new and I am thrilled that it was so easy. Thanks

unplugged and installed

had to pull range away from wall and unplug it so we could get behind to access the rear panel. we then removed old terminal block, by, removing screws from back panel, and one screw from under burner drip pan, inserted, new block, and reassembled. plugged it in to test and burner worked properly.