JCGS650SEF3SS General Electric Range - Instructions

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

I just followed the instructions on the link provided with the part

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.

Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

Took longer to open the box.

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.