CC2S985SET8SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Harkers Is., NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven slow to heat up
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Chambersburg, PA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element not working
Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Annapolis, MD
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
The oven temperature could not be controlled
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Palm Coast, FL
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Total Burn Out Of Original Broiler Element
Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from protection, KS
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
element burnt out
ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Dallas, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
bakinf element not working
best to pull stove out away from wall connect from behind stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hamden, CT
- Parts Used:
- WB30X46987
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Wires to attach to bake element retracted into stove body
I had to remove the back panel on the stove to free up taped wires to get more length.
Was this instruction helpful to you?
Thank you for voting!