RCK524GS-1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- don from Dallas, TX
- Parts Used:
- WB48T10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing racks
took the old ones out and put the new ones in their slots. No issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mervin from Ramona, OK
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broiler stopped working. Wouldn't toast my toast.
I thought because the broiler was off that I could remove the element with not problem. As I was pulling the element out, it sparked, melting something in the back I couldn't see at the time. I immediately went to the breaker box and turned the power to the oven off. After I found the website online I was very gratified to see how easy it was to identify the element I needed and order it. I removed the old element. One of the wires from the element slipped through the hole in the back of the oven. To get at it I had to unscrew the four screws around the outside edge of the oven and pull the whole oven out. I had a table handy that I pulled up next to the oven and set it on without disconnecting the main wiring. After getting the oven out I removed the six or so screws on the coverplate and easily found the loose wire. I pushed the wire back through the hole in the back of the oven and made sure it would not fall back into the hole. I put the back plate on with all its screws; pushed the oven back into its hole and screwed the four screws in around the edge that hold the oven in. Then I attatched the broiler element to the spade connectors and screwed it back in place. I turned the breaker switch back on and tested it. It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Fairport, NY
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broiler element would not heat
After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worked once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Orlando, FL
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Clips needed to re attach heating element
Pulled out old with pliers. Twisted new clips in per instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from GROVE CITY, OH
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
element was bad, not heating
had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from Stockton, CA
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Burned out broiler element
After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pushed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Decatur, IL
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element melted down
Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herman from Norman Park, GA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken element
Used nut driver, removed 2 screws and removed old element. Reversed procedure for installion of new part. Can't believe ordered part one day & recieved it next day. Fantastic service. Will definitely call company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CORY from CARY, NC
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake element caught fire and started sparking
Installation was really easy. Remove the old bake element, plug the new one in, took at most 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Glen Island, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace end caps
The video was very helpful.Very easey repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Plainfield, IN
- Parts Used:
- WB15K5068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven handle broke
Removed the door and four screws to get to handle. Removed the two screws holding the handle and replaced with new handle. Replaced the four screws on the door and reconnected to oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tammy from newberg, OR
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
top oven bake element blew up
When i finally got the right part.It only took few minutes to screw in and it worked perfectly.Customer support was very helpful in finding the correct part.thanks
Was this instruction helpful to you?
Thank you for voting!
Borken Glass & oven handle left side.
Replaced Glass & filed of plastic tits on handel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from N Las Vegas, NV
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower Element Partially Heating
I removed the two screws holding the element in, pulled it out, and unplugged it. Installation was reverse of removal. It's just that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Mars, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
End cap plastic broke at screw entry
Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty easy fix.
Was this instruction helpful to you?
Thank you for voting!