JGSP28SER2SS General Electric Range - Instructions

Nylon support is attached to the oven frame with a screw having a .25 inch socket head. The screw is mounted in a recessed opening on the support, so a socket is needed. I needed to purchase a proper size socket from the hardware store for a few dollars since the smallest one I had was 7mm. I guessed at the size and was correct. Repair was easy and took a few minutes.

The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.

I was at my in-laws and they expressed how they needed to buy a new stove, since it stopped working. They explained the problem to me and I immediately checked the broiled (it worked fine). Knowing that stoves have 2 electric igniters, i knew 1 was bad.
The site got me the part in 3 days (regular shipping).
The repair was pretty easy.
- Removed 2 screws that hold the floor of the oven.
- Removed 2 nuts that held the igniter to the oven.
- Removed the bottom drawer of the oven, and unplugged the igniter.
- Finally, I screwed in the new igniter, fed the wire down to the plug and plugged it in.
- Then I tested the oven before putting it back together, IT WORKED!)
The only negative was, when I was removing the racks and pans from the oven, one of them happened to be filled with oil for frying, and it got all over me. Be prepared for anything when working on someone else's appliance.

Over a duration the oven burner would take time to light, then eventually not ignite at all, so repaired ignitor and alls good. Easy, easy, didn't have to disconnect gas, electric for safety.

I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.

Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

Although the original oven design called for a round igniter, the most recent replacement, done by a service mechanic, utilized a flat igniter. I compared the appearance of this flat igniter to the igniters offered by PartSelect and found that the GE igniter (not the Roper which cost twice as much) matched exactly. I installed it and that solved the problem (of insufficient igniter heat to turn on the gas).

Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.

removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.

I got my part in a couple of days during christmas and still got at pretty quick it was 5 screws unpluged the old one pluged in the new one put screws back and we were ready to cook, did all from inside the oven did not even move the stove very simple!!

My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.

thank you

Replaced the igniter. Quite simple.

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.

removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!