CCS975SD2SS General Electric Range - Instructions

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Really easy. Part came in rapid time and was the right part. Went on web and got instructions with video how to install.

I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to the range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!

Use a 1/4" nutdriver and remove the screws that are on the bottom corners of the range top.Prop up the range top high enough for ease of using 1/4" nut driver. Take a picture of the wiring for future reference on re-installing wiring. Note arrow location on burner and remove 1/4" screws holding the clamps to the burner in place and place to the side for re-install on new burner.Remove wiring off old burner.Hold new burner in place with arrow location in previous location and notice holes where clamps will go. Screw clamps on burner using original screws and snap in mounting slots on stove.Re-install wiring.Lower range top and re install 2 screws , 1 in each corner under range top. Test for proper operation and enjoy!

The unit has two spring clips that hold it in place. Also two screws that hold the element to the clips. It comes apart ok but doesn't go back as easy. I didn't remove the top as there was room to work from under it.

My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in place . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.

Thank you PartSelect for all your help !!

Easy

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

I got someone to look at the stove. They told me what I needed. I looked all over the Internet and couldn't find the part. One guy told me just to buy a new stove top because mine was an antique. It still looked good and two burners were still working. I didn't give up. I found the part on partselect bsite and was thrilled. It shipped fast and was exactly the right part. Now my stove works like new.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.