18471-1 General Electric Range - Instructions

Removed stove top from counter, removed glass top by removing 10 phillps screws, removed control bracked, unplugged connectors(wires) on old control and plugged into the correct position on the new control, replace control on the bracket then reinstalled the stove top and placed the stove top back into counter.

disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.

Opened oven door removed screw and broken end cap. Replaced with new end cap and put handle back on

Turned of the electric at the circuit breaker. Removed the cable clamps for the electric feed cable to enable free movement of cooktop. Lifted cooktop from the counter and propped up on counter ledge. Removed control knobs. Removed perimeter screws, 8 phillips, from around the edge of the cook top surface where it attaches to the sheet metal housing and lifted glass top off. Removed the failed burner and disconnected the four electrical leads. Removed the mounting tabs from the old burner and installed them on the new burner. Attached the electrical leads to the new burner and tightened with pliers. Reattached glass top and knobs, reinstalled in counter, clamped the electrical cable, flipped the breaker and tested. All good.

Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!

Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless

Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

There are 18 sheetmetal screws not 8
The GE SREWS HAVE AN INTEGRATED WASHER which causes the philips head to STRIP these needed to be drilled out!!!
The glass top was GLUED to the sheetmetal box and did not come off without a fight

remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy

Required removing the door, by sliding it off the hinges (open 1/4 then lift up), removing the outer frame which releases the inner glass door section exposing the door end screws. Removed the phillips head screw on each door end releasing the old handle. Inserted the new handle in the ends, screws replaced, reversing the above. Thanks for the correct part. Byron C.

I ordered the part, It came a few days later,,Within 15-20 minutes, I had it installed..Pretty easy...Thanks

Unscrewed bottom screws, replaced trim. No trouble.

Removed old part by removing the screws at the boottom of the oven door. I wasn't sure if the glass oven door cover would remain in place once the trim piece was removed, fortunately I was ready when it came down. The glass cover is large and heavy so you need to be ready to handle the bulk of this piece once the last screw is removed. Cleaned everything and with the help of my wife, who secured the oven door cover in place, secured the new trim piece by replacing the screws. What a difference, looks like new! PartSelect provided great service in terms of speed and part acciracy.