CCGS990SET5SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from milford, CT
- Parts Used:
- WB03K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stripped control knob
remove and replace the same .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Coventry, RI
- Parts Used:
- WB49K10037
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter
Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from Mt. Bethel, PA
- Parts Used:
- WB03K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the original knobs were plastic and cheap and cracked within a year
pull off old ones, which wasn't hard because they were cracked. push new ones in. Some were a little harder than others but all went in with a little push.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria E from Walnut, CA
- Parts Used:
- WB03K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Original burner broke
Just push the burner knob in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Dana Point, CA
- Parts Used:
- WB03K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic burner knobs provided by G.E.
Slide new, better quality knobs into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Ft. Washington, PA
- Parts Used:
- WB02K10254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from East Williston, NY
- Parts Used:
- WB16K10062, WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner cap did not fit burner, causing ignition failure
Replaced burner. New burner now ignites properly.
Was this instruction helpful to you?
Thank you for voting!