JCKS06WR-2 General Electric Range - Instructions

removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.

turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.

First I turned off the power at the fuse box, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced with the new element. Very Easy!

Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.

Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!

I had to struggle to get the pliers to grab hold of the screw because they were so tight. I was worried about "stripping the screws" but finally they loosened and I got them both out. My friend was holding the flashlight, so that helped. I was not real sure what to do next but the wires popped off the element so it was clear that all I had to do was pop the new one on. Easy. I had the most trouble trying to get the screws out. I saved myself $$$. Thanks for your help in sending the correct part!

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.

removed and replaced

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

took the old ones out and put the new ones in their slots. No issues

Bake element was glowing. . . Then by the morning, a "cancer-like" thingy traveled the length of it!after kicking off the breaker, I brought the broil down to the bake>. It worked (not recomended>. . But it worked for me). Came the new element, in 2 days. . . And all is back (the broil slots didn't line up so it was a redneck install at best til I got it back to normal). They should add the owner's faces to mt rushmore! Bless you all!

had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.