JCBS250ST4SS General Electric Range - Instructions

Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!

I ordered part at 10am on Monday and part arrived at Noon on Tuesday 24 hours WHAT MORE can I say... It was all easy and now I have to cook again, so much for the stove is broken excuse.

UNPLUG the oven. Following what every else was doing, I removed the element first, then disconnected the contacts. The leads on the contacts are not overly long, so I found myself removing cover on rear of oven when reconnecting red and yellow wires. Required removing two more screws with nut driver. Should I have to replace another element, I would remove rear cover first, unplug wires from element, remove element. Reverse procedure with new element.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.

Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

Removed insulation, took stove apart, power washed all parts, repaired wires, re assembled with rock-wool insulation. The insulation I purchased here seemed too light, about what would be expected for a dishwasher, it was also much too small, only covered a little over half the oven.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

Replaced element control switches

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Followed the directions!

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.