Models > JCAS730M2WW > Instructions

JCAS730M2WW General Electric Range - Instructions

Jump to:

All Instructions for the JCAS730M2WW
76 - 90 of 115
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Michael from West Monroe, LA
Parts Used:
WB17T10006
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
plastic adapter was broken on end of the block kit
unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas
Was this instruction helpful to you?
Thank you for voting!
Customer:
Henry from Norwich, CT
Parts Used:
WB17T10006
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Burner not heating
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mohammed from San Jose, CA
Parts Used:
WB17T10006
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
none to occasional power to burner elements
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sue from Fort Oglethorpe, GA
Parts Used:
WB17T10006
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The burner would not work.
I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.
Was this instruction helpful to you?
Thank you for voting!
Customer:
loma from Neah Bay, WA
Parts Used:
WB02K10062
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Drawer glider broke about a year ago.
My wife could open and close the drawer without too much difficulty, but occasionally, it would not close properly and she would have to empty the contents do could alaign it properly to close. The last time she was talking about buying a whole new drawer. I asked her what the part looked like, as I never to fight with it. I went online and found the part for $1.16 plus shipping at $8 plus. It was well worth the time and effort, and I now have a happy wife. Paul Parker
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert W from Whitehall, PA
Parts Used:
WB24T10025
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Burner went to high heat at any setting
Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from Keezletown, VA
Parts Used:
WB24T10029
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Replacment of burner control switches
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from Chipley, FL
Parts Used:
WB24T10025
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench set
burners would go to full high heat& not reduce down.
Hubby did the job..all went well except for the arthritis & having to bend pull stove out from wall ,pushing back..ha-ha.
Was this instruction helpful to you?
Thank you for voting!
Customer:
LEE from ROME, GA
Parts Used:
WB24T10025
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Large eye would over heat when was on med. settings
I unpluged the stove pulled it out and took the 6 screws off the back to get to the switch. Around front take knob off and removed the two screws holding the swich in place and pulled it out the back. Pulled one wire at a time off of the old switch and replace on the new switch. Nothing to it had it done in just a few mins.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Felipe from Donna, TX
Parts Used:
WB24T10025
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The burner combusted burning the the burner switch
Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Jericho, VT
Parts Used:
WB24T10025
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Burner was always on high when on.
Disconnected the power. Removed hex head screws from top and lower rear panel. I think there were 8 all together. Pull the knob of the burner control, removed two screws that held the switch in place. Moved the wires one at a time to the new switch, re-assembled. Burner worked properly. Very easy to find the right part from this web-site, and the instructions from others like this were helpful. Easy fix!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Curt from Maple Grove, MN
Parts Used:
WB24T10025
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Burner light would not shut off
Checked each burner switch by disconnecting the light indicator wire. Located the switch, replaced the switch and the indicator light operated as it should.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Woodbridge, VA
Parts Used:
WB25T10041
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Orange light "Hot Stovetop" lense broke off.
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Orlando, FL
Parts Used:
WB2X9719
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Clips needed to re attach heating element
Pulled out old with pliers. Twisted new clips in per instructions.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary Ann from Granby, CT
Parts Used:
WB02K10062
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Plastic glide broke
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JCAS730M2WW
76 - 90 of 115