JCBP35CL1CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MIGUEL from NEW HAVEN, CT
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the terminal was broken and rusting so the burner was not heating well
Removed the back cover with a socket tool, unplugged the old terminal and plugged in the new one. there is a screw holding the terminal block. so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sebring, FL
- Parts Used:
- WB2X8228
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Front burner would not heat
Since the unit is a drop-in range I had to remove the heat shield/drip plate to thread the wires from the control button to the receptable. The replacement part wires were to short to make the connection so I have to use some of the wiring from the old receptable to make the connection. That is the reason for using the wire cutter and connecters.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gayle from genoa city, WI
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
There ws no heat on elements
I first unpluged the stove then removed the 6" element then I removed the back panel on the stove located the wires that went to that element unplugged them and removed the block then fished the wires through for new terminal block installed in terminal block bracket then pluged in wires put element in place put back panel back in place plugged stove checkout heat on element good to go 20 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Paris, TN
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
F2 error when oven was heating up, along with a beeping noise and then it shut off
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Loveland, CO
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
fried oven control using raid
replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel J. from Vernon, CT
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace old burner bowls
It was easy to just replace the old burner bowls rather than try to clean them. The peices ordered from Parts Select were a perfect match and they arrived on a timely basis.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolee from Carson City, NV
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change out burner bowls
Took out the old ones and replaced with the new ones. Very simple task. It didn't take 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Canandaigua, NY
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
top burner terminal block burned put due to heavy use
Disconnected power supply to range, pull top back metal cover, pull wires from burner on/off switch,and removed one screw that holds block in place. Installed new terminal block by placing screw back on block & placing wires back on the on/off switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Quarryville, PA
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original drip pans scrubbed so much-rusted....
Took out the original drip pans and set in replacements which I ordered in black enamel.
Slipped right in and look great as the oven door glass is also black. Look like they came with the range.
Slipped right in and look great as the oven door glass is also black. Look like they came with the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Atwater, OH
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out terminal block
It was as easy as you said. I took the back off, removed the screws holding the terminal, un-hooked it and put the new on on. Replaced the back and wa-la! Working burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Lubbock, TX
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Drip Pans on Stove Top
Just removed the old drip pans and then inserted new ones...pretty dog gone easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from townshend, VT
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was not getting up to temp
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vance from williston, ND
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The burner had been replaced and it shorted out ;thus discovered thath the wiring block kit was faulty. The parts ordered were a snap to replace the original .
Shut the power off and unscrewed facial hardware ,unplugged terminal and unscrewed hold down bracket and redid everything that I mentioned above. For a rookie it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patty A from Noblesville, IN
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The stove's burner bowls were dirty and old and the chrome was gone where the cooking drippings had collected under the previous owner's usage.
We simply typed in the model of the range and several selections of replacements came up on your website. We ordered the black porcelain ones to replace the old chrome ones, thinking they might hold up better and be easier to clean. They look great and I really think they WILL be easy to wipe up. Thank you, Part Select! Patty in Indiana
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Corvallis, OR
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Incorrect Burner Bowls
For 12 years I've been suffering with the incorrect burner bowls...I love to cook and it's really irritating when your bowls don't fit correctly. Now, I am amazed at how my burners fit! Thank you! What a Blessing!
Was this instruction helpful to you?
Thank you for voting!