JCBP27WL1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Philadelphia, PA
- Parts Used:
- WB02K10158
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer sticking and not operating smoothly
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from BOULDER, WY
- Parts Used:
- WB02K10158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drawer support broke
Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Sarasota, FL
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rusted trim strip
remove screws, re-install screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from West Melbourne, FL
- Parts Used:
- WB07K10250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from GAYLORD, MI
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
front lift burner not working and surface light on with everything off
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from HOPEWELL, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Just didn't work no pwr to it
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDENTON, NC
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Defective switch
Replaced element control switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RANCHO MIRAGE, CA
- Parts Used:
- WB02K10061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glider
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from newport news, VA
- Parts Used:
- WB31T10015, WB31T10014, WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
stove surface unit arced and caught fire/sparks
I first unplugged the stove (alternatively, shut off the breaker). I unscrewed the terminal block screw from the stove top (after removing the stove element and burner bowl). I got in behind and removed the six screws in the sheet metal panel. Removed the panel. Unplugged the terminal block wires for each unit, one at a time, and immediately plugged in the new unit wires (after threading the wires up under the control panel). Wire polarity doesn't matter. Secured the panel temporarily with a couple of screws. Replaced the burner bowls and stove elements in the new terminal blocks. Plugged in the stove and tried each unit. Worked great! Secured the remaining screws in the rear panel and moved the stove back into place. Thanks so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Crumpler, NC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven temp wouldn't regulate.
Followed the directions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannene from HUNTINGTON, TX
- Parts Used:
- WB07K10250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part rusted over time...22 years.
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from E WENATCHEE, WA
- Parts Used:
- WB31T10015, WB31T10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
just needed new GE burner bowls
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from FAYETTEVILLE, NY
- Parts Used:
- WB07K10250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICKEY from MONTROSE, NY
- Parts Used:
- WB25T10041
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lens snapped off on the inside-plug was left loose
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this instruction helpful to you?
Thank you for voting!