JCBP270DT1BB General Electric Range - Instructions

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.

I ordered part at 10am on Monday and part arrived at Noon on Tuesday 24 hours WHAT MORE can I say... It was all easy and now I have to cook again, so much for the stove is broken excuse.

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.

UNPLUG the oven. Following what every else was doing, I removed the element first, then disconnected the contacts. The leads on the contacts are not overly long, so I found myself removing cover on rear of oven when reconnecting red and yellow wires. Required removing two more screws with nut driver. Should I have to replace another element, I would remove rear cover first, unplug wires from element, remove element. Reverse procedure with new element.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.

Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.

Removed the old element and burner bowls and replaced them with the new ones! No screws, no tools needed. PartSelect's prices are cheaper than any other place on the Internet and they shipped me genuine replacement parts, not some 3rd party no-name brand. Also, shipping took less than 2 days! I am thoroughly impressed.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.